30 Openings Plywood Hot Press

Hot selling multi opening hot laminate press for plywood machine. The series of hot press machine apply to processing furniture ,film faced plywood.You can use it to press the plywood plank or laminate the wood veneer, film paper or melamine paper on plywood ,chipboard or MDF.
Chat Now

Product Details

30layers hot press Specification
Model:XHC48-30-3-320-42-7030 Openings 600T
Total pressure 600T
Board feeding direction Transverse
Layers 30 layers
Layer spacing 80MM
Hot press plateNumber of hot press plate:31pcs
Size:2700*1350*42(single inlet and outlet)
Material:Q235B
 Cylinder for hot press machine (3pcs)3PCS(cylinders)*320mm
Wuxi cylinder
Seal:4pcs rubber seals per pcs of cylinder
Stroke:2400mm
Hydraulic system for hot press machineCompression resistance:25Mpa
Low pressure pump flowing:315ML/R
High pressure pump flowing:31ML/R
Motor power:18.5kw+18.5kw+18.5kw
Closing time:36s
Overall dimension 3555*1350*6400mm
Weightabout 65T

Heating treatment
Thickness of the frameComposite frame :AssembleDetachable
Upper and bottom beam:1200mm and1100mm
Main boby:30mm,Q235
Middle beam:500mm
 Table lift(gantry-type) (with roller chains)+one set of power roller(1500*2100mm)Overall dimension:4155*1100x6500MMDetachable
2*63mm
Working stroke:4600mm
Weight:About 2.5T
Load bearing:about 2T
loader30 openingsDetachable
Overall dimension:4000*2050*5600MM
Weight:About 6.2T
unloading30 openings,with 4 pcs fans+for two veneerDetachable
Overall dimension:3350*2700*4600MM
Weight:About 3.2T
automatic constant temperature system (2sets)DN40 steam pump,other valves(2sets)for steam boiler

We suggest that Process above 3mm-25mm veneer

30 openings plywood hot press

1) Simple combined structure ,easy for transportation, installation and maintenance
2) Adopting advanced world famous brand components in hydraulic parts ,electric parts and operation parts.
3) Lifting cylinder to accelerate the closing and opening time and with much less working noise.
4) Running in a high automation and Intelligent, no pollution 
5) Working with the pressure detector system and controlled system running by solenoid valve.


Unloading system:

The hot press daylight and thickness of hot plates which decides how much the height of each layers. Discharging rack is made of the main frame , fan, axial flow fan, pulley frame, pulley support plate and support circular tubes.

image


After the press finishing, the boards will be took manually, plate in artificial falling into the drying plate rack, the direction of plate limit lever block board does not run out of the air board frame, rebound institutions closed to prevent plate rebound back to hot pressing machine, fan automatically open, to lower die before publication, artificial board.

1.Keep the center line of the drying rack and hot plates.

2. According to the figure, checking the plane position of the discharging rack.

3. Adjust the discharging position.

4.Adjust the horizontal height to keep pulley of bus bar and the hot plates on the same plane.

5.To weld the discharging rack and hot press.

6.Install the fan.

image

Lifter(Gantry type)

Lift is made of ①Column, ②upper beam, ③wire rope, ④insurance mechanism, ⑤ oil cylinder, ⑥guide seat assembly, ⑦platform, ⑧buffer column, oil circuit system and electric control.(Picture3)

image


1、To clean the surface of the foundation and check the ground height is 660mm and the position of installation which the error is less than 2mm.

2、 To install the column first, adjust the column frame inner size is 3240 (4 * 8 feet 3540) and the error is ±2. The column and ground vertical degree is less than 5 mm, and then welding to fix with the steel plate and connect to the hot press .

3、To fix the crossbeam with the help of the forklift truck and then install the wire rope.

4、To fix the platform with the guide pad and ensure that the surface of the platform is flat with the ground. And then lock the wire rope.

5、After adjustment, weld to the embedded iron directly.

6、 To install the tubing and wiring.

Loader system


      1.frame-type base, with two parallel rigid structures, supporting the entire automatic feed rack. The bottom hole is drilled by the foot screw hole and the whole base is fixed to the ground.

      2.Main frame. Using a detachable structure, the top and bottom are rigid rectangular frames, which are connected by four parallel columns. The vertical column and the upper and lower frame are connected by thread. The lower end of the main frame is provided with four supporting wheels, which can be pushed out of the whole board frame when the maintenance test is mounted or the stainless steel plate of the hot press is replaced, and the maintenance space is given out.

    3.Moving rack. Adopt the gantry-type, the both ends of the drive shaft fixed transmission gear which makes the power transmission to both sides of the synchronous rotary shaft.

     4. Feeding rack. The plate rack is used for conveying the slab into the hot plate of the press. The front end is fixed to the walking frame by the t-screw, and the rear end is supported by the nylon support wheel on the main frame.

     5.Baffle rack. Install the front end of the main frame, and rely on the forward power of the feeder rack to lift the baffle frame forward, and then drop it back to the baffle position with its own gravity.



Inquiry